Bm 81111 AUTOMATIC SHIFTER, STEALTH PRO BANDIT MAGNUM User Manual download pdf

9500773-01

Printed in the U.S.A.

The B&M Magnum Grip Pro Bandit

Shifter is a gate pattern type shifter

mechanism. It is available in a rear exit

cable model only and it is designed for

Powerglide transmissions with standard

or reverse pattern valve bodies. The

B&M Magnum Grip Pro Bandit

Shifter features a positive reverse

lockout mechanism and a neutral safety

switch as required by NHRA and IHRA.

Please read the instructions and review

the illustrations thoroughly before

beginning the installation.

IMPORTANT: You must first install

the shifter cable and an air slave cylin-

der (such as B&M's #80883 KIT) or

electric solenoid onto the shifter before

positioning it in your vehicle. This is to

insure that you allow for proper clear-

ance at the rear of the shifter for these

components before you permanently

mount the shifter body into the vehicle.

Mounting the shifter first without the

cable and the air slave cylinder at-

tached can cause possible interfer-

ence from frame rails or other compo-

nents. Poor cable routing and cable

binding will result in poor shifter opera-

tion.

INSTALLING THE SHIFTER CABLE

STEP 1. Pull the shifter stick all the

way back to the Low gear position, the

position furthest from the red reverse

lockout release lever. Remove the five

countersunk screws from the B&M

Magnum Grip Pro Bandit Shifter

cover (See Photo #1).

STEP 2. Locate the cable attachment

pin at the rear of the shifter stick. The

pin is visible just under the black shift

pattern gate plate. Do not remove the

black gate plate (See Photo #2).

STEP 3. Fully extend the stamped

loop end of the shifter cable #80834

(included in #81045 KIT), (See Photo

#3).

STEP 4. Insert the extended stamped

loop end of the cable through the larg-

est access hole in the rear of the shifter

body. Slip the stamped loop cable end

over the cable attachment pin at the

rear of the shifter stick and attach the

supplied e-clip to the pin. Check to

make sure you have the e-clip firmly

and accurately in the locating groove in

the pin (See Photo #4).

STEP 5. Push the cable anchor tab

flush to the rear of the shifter body.

Installation Instructions

Magnum Grip Pro Bandit

Shifter

Part Number 81045 & 81046

(Visit www.bmracing.com for additional products and product information)

Photo #1

1 2 3 4 5 6 7

Summary of Contents

Page 1 - Magnum Grip Pro Bandit

9500773-01Printed in the U.S.A.The B&M Magnum Grip Pro BanditShifter is a gate pattern type shiftermechanism. It is available in a rear exitcable

Page 2 - (OPTIONAL PRODUCT)

Align the 17/64" cable flange hole withthe 9/32" hole in the shifter body. Besure to use the hole directly above thelarge cable access hole

Page 3

stalled. Before you proceed with mock-ing up the B&M Magnum Grip ProBandit Shifter in your vehicle, tempo-rarily reinstall the side cover with the

Page 4

anchor, be accurate.Mounting the cable anchor to thechassis is not recommended. Thecable should always be mounted tothe (engine/transmission) combina-

Page 5

disconnect extension onto the 10-32threaded cable end. Leave the jam nutand the extension loose. Install themale ball pin from the #80323 quickdisconn

Page 6

tion. The trigger is not required to pullthe stick back to Low gear from Neu-tral. The third detent will be the Highgear position and the fourth deten

Page 7

7CHASSIS

Comments to this Manuals

No comments

Bm 81111 AUTOMATIC SHIFTER, STEALTH PRO BANDIT MAGNUM User Manual

Browse online or download User Manual for For the car Bm 81111 AUTOMATIC SHIFTER, STEALTH PRO BANDIT MAGNUM. B&amp;M 81111 AUTOMATIC SHIFTER, STEALTH PRO BANDIT MAGNUM WITHOUT ACCESSORIES User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Bm 81111 AUTOMATIC SHIFTER, STEALTH PRO BANDIT MAGNUM

Browse online or download User Manual for For the car Bm 81111 AUTOMATIC SHIFTER, STEALTH PRO BANDIT MAGNUM. B&M 81111 AUTOMATIC SHIFTER, STEALTH PRO BANDIT MAGNUM WITHOUT ACCESSORIES User Manual